3~20KW Electric-start Diesel Generator-set ☚


Product HS code for import custom use: 85023900


Note:

All models could be in choice of Open-Frame type or Silent type, available with or without auto-starting system.


3~8KW silent type Generator

10~20KW open frame type Generator

10~20KW silent type Generator

Data sheet

Gen-set Genset Model YL-3 YL-5 YL-8 YL-10 YL-12 YL-15 YL-18 YL-20
Power Capacity (kva) prime 3 KW 5 KW 8 KW 10 KW 12 KW 15 KW 18 KW 20 KW
Rated Voltage Volt 110/220 V ; 120/240 V 380/220 V
Rated Current A 5.4 9 14.4 18 21.6 27 32.4 36
Rated Frequency Hz 50 50
Power Factor Cosφ 1.0 Lagging Cosφ 1.0 Lagging
Cooling System Air-cooling Water-cooling
Overall Dimension (L×W×H) mm 950×540×690 1600×900×1500 1700×1000×1500
N.W. & G.W. kg 150 / 155 540 / 550 600 / 615 700 / 720
Noise(B) db 69 / 70 68 70
Diesel Engine Engine Brand Chinese brand YUCHAI
Engine Model 186 YC2108D YC2115D
Engine Structure Single Cylinder
4 strokes
Horizontal type
Double Cylinder, 4 strokes, Horizontal type
Bore × Stroke mm None 108 × 120 115 × 120
Fuel tank Silent type, all with fuel tank Silent type is all with fuel tank but Open frame
type is without fueltank. Fuel tank could
be supplied in extr cost upon request.
Fuel tank Capacity litre 16 40
Engine oil Capacity litre 1.65 10 11 12 13 14
Fuel Consumption g/kw.h 283 250 249 248 248 242
Rotating Speed RPM 3000 1500
Starting Method Electric By 12V batteries By 12V batteries
Alternator Features Brush, self-excitation, constant
voltage, full copper wire
Brush, self-excitation, constant voltage, full copper wire
Insulation Class H Class H
Phase 380V / 3 phase 4 wire / Y type 380V / 3 phase 4 wire / Y type

Remind:

  • 1) Strictly follow the Oil dipstick to add in engine oil with the oil gauge shall not exceed the upper limit or below the lower limit of the dipstick scale.
  • 2) Engine oil should be changed in the 1st time of 20 hours after new machine running, 2nd change will be 60 hours after and later, each 250 hours you need to change the engine oil.

You may find in each generator a steel data plate with information in Chinese, here comes the English information as below:

ATTENTION

  • 1) Generator should be kept clean to avoid any dirt, water droplets, metal fragments or other debris intrusion;
  • 2) Generator MUST BE GOOD GROUNDED;
  • 3) Generator power output cable should be sufficient with enough cross-sectional area and good connected with the appliance;
  • 4) DO NOT run the generator at a overload situation;
  • 5) ALWAYS balance the phase loading level of triple phases;
  • 6) Rated output data on this plate is for THREE-PHASE generator ONLY, DO NOT use it as single-phase rated output;
  • 7) Check regularly the generator brush and lubrication of the bearing chamber to avoid unexpected abrasion;
  • 8) ALWAYS make the wire connecting in strict accordance with the wiring guidance.

Procedure of generator start up

  • 1) Disconnect the output air switch;
  • 2) Starting up the generator until the runner speed up to no-load level;
  • 3) Adjust the AVR (automatic voltage regulator) to prospective appliance voltage value;
  • 4) Connect the output air switch and then load the appliances into the generating system one by one;

Procedure of generator stop off

  • 1) Stop off all appliances to remove all electric loading;
  • 2) Disconnect the output air switch;
  • 3) Stop the generator.